家具測試儀,家具綜合測試儀,家具疲勞測試儀
一、功能沙發沖擊跌落試驗機用途:本產品測試座部沖擊、扶手沖擊、擱腿沖擊。
二、依據標準本儀器引用標準:En4875。
三、儀器規格 項目 規格顯示方式 數顯高度顯示儀跌落高度 3英寸~16英寸(75mm~406mm)測試次數 0~32000次試件*大尺寸 (L×W×H) 1000×1000×1200mm 跌落袋重量 75lb、200lb 外型尺寸 (L×W×H) 1600×1300×2500mm 電源 3∮,AC380V,50HZ,1HP 重量(約) 約380kg 傳動方式 電動傳動 如需更詳細信息,歡迎來電咨詢!!家具測試儀
沙發檢測儀器設備,沙發測試儀器設備,沙發試驗機,沙發測試儀,沙發測試機,沙發試驗儀,沙發沖擊測試!
其他家具綜合測試儀的測試項目介紹:
家具綜合測試儀,椅子測試儀器
測試項目:座面,靠背。
座椅座面的試驗方法
Test Method for Seat Chair and seat surface:
1.座面的靜載荷試驗:通過加載塊垂直向下施加一定力量于加載點上并保持至少10秒。并反復進行10次。
Seat Surface Static Load Test:
vertically down through the loading block to exert force on the load point and keep at least 10 seconds. And repeated 10 times
2.座面的疲勞試驗:通過載入墊,將950N的力和規定的次數垂直向下重復施加在座面載入點上。加載速率為每分鐘不超過40次。家具測試儀
Fatigue test of the seat: by loading pad, put 950N force and the specified times to repeat vertically down impose to the load point of the seat surface. Loading rate no more than 40 times per minute
3.座面的沖擊試驗:將一塊泡沫塑料放在座面上,然后把座面沖擊器置于規定的高度,使其自由跌落,沖擊載入部位各10次。
Impact test of the seat: put a piece of foam on the seat surface, then place the impactor of the seat in a specified height and make it fall freely. impact loading site 10 times each.
家具綜合測試儀,座椅靠背的試驗方法:
Test methods for back of the chair
1.座背的靜載荷試驗:用擋塊靠住椅和凳子的腳上。然后將規定的平衡載荷施加于座面載入點上。再將規定的力沿著與椅背垂直的方向通過載入墊施加于載入點上。每次至少保持10秒。并反復進行10次。家具測試儀
Static Load Test for back of the chair: put the baffle on the chair leg. Then impose the specified balance loading to the load point of the seat. And then provides the force perpendicular to the direction along the back pad by loading imposed on the load point. To keep at least 10 seconds each. And repeated 10 times.
2.座背的疲勞試驗:用擋塊靠住椅或者凳子的腳上,然后將950N的力垂直施加在座面載入點上,再通過椅背載入塊,將330N的力按規定的次數施加在椅背的載入點上。加載速率為每份鐘不超過40次。
Fatigue test of the seat back : use the block fixed the feet of the chair and then impose the 950N force vertically to the surface load point, through the back loading block. Impose 330 N force with specified times to the back loading site. Loading rate no more than 40 times per minute.
家具綜合測試儀,桌子測試儀器
測試項目:桌子的穩定性和桌面沖擊。
1、 垂直負載下的穩定性試驗:
Stability test of the vertical load
把試件放在試驗基面上。在其*不穩定桌邊中心離邊沿向內
Place test specimen on the base surface. Impose the force to the table in its center from the edge of the most unstable inward
2.垂直和水平載入穩定性試驗:家具測試儀
Vertical and horizontal load stability test
把試件放在試驗基面上。用擋塊擋住試件*不穩定邊的桌腳。防止試件在試驗中移動。在該邊中心離邊沿向內
Put the specimen on the test-based surface. With the block blocking the most unstable side of the specimen legs to prevent the test specimen to move. The edge center from the edge inward
3.垂直靜載荷試驗:
Vertical static load test
在桌面易于發生破壞的位置,按規定的力通過載入墊,垂直向下重復施加10次。每次至少應保持10秒。家具測試儀
On the most easy damaged position of the desk surface , to impose the specified force by loading pad, vertical put down repeated 10 times. Keep 10 seconds at least.
Desktop sustained vertical load test
椅子測試儀器
測試項目:座面沖擊
家具綜合測試儀座面的沖擊試驗:將一塊泡沫塑料放在座面上,然后把座面沖擊器置于規定的高度,使其自由跌落,沖擊載入部位各10次。
Impact test of the seat: put a piece of foam on the seat surface, then place the impactor of the seat in a specified height and make it fall freely. impact loading site 10 times each.
歐洲市場 家具綜合測試儀
測試標準:根據EN1335-1:2000
辦公家具-辦公座椅對尺寸要求的測試項目
1、座椅高度、長度、寬度
2、座椅表面的長度
3、座椅表面的傾斜度
4、從座椅表面起椅背支撐點的高度、椅背靠墊的高度、座椅表面起椅背的高度
5、椅背的寬度
6、椅背的水平半徑
7、椅背傾斜調整幅度
8、扶手的長度
9、扶手的寬度
10、坐墊至扶手的高度
11、從扶手前方到座椅前邊緣的距離
12、兩個扶手的間距
13、底座*大的支架
14、穩定度
測試標準:依據EN1335-2:2000 家具測試儀
辦公家具-辦公座椅的**檢測要求
1、一般設計上的要求
2、測試的順序
3、使用期間的穩定度
4、空載時座椅滾動的阻力
5、強度及耐久度
6、使用信息
測試標準:根據EN1335-3:2000
辦公家具-辦公座椅的**檢測方法(穩定度的檢測要求)
1、前端的失衡測試
2、向前的失衡測試
3、側面的失衡測試
4、向后的失衡測試
測試標準:依照EN1022:1997對穩定度的測試要求
適用于各類座椅的實驗方式
1、座椅的向前失衡測試 家具測試儀
2、無扶手座椅的側面失衡測試
3、有扶手座椅的向后失衡測試
4、有椅背座椅的向后失衡測試
座椅實驗方式的幾何變數
1、一般檢測
2、可傾斜座椅
3、搖椅
4、有腳凳的活動躺椅
5、腳凳測試
6、無腳凳的活動躺椅
座機:0769-88838200 手機:13602382905